Description
If you need more transmitter, please buy Product ID: 1514059Feature: Working voltage: DC12VStatic working current: ?10mAWorking temperature: -40°C to +80°CReceive sensitivity: ?-95dBWorking frequency: 433.92MHZOutput current: ?10AWorking mode: Jog, self-locking, interlocking, delay (adjustable)Output mode: Contact output (controllable AC, DC) Scope of application: This product is controlled by intelligent microprocessor, which can be applied to garage door control, lighting control, remote control curtains, access control system and various motor control systems. Small size, easy to install, safe and reliable to use.The 12V 1-channel learning code remote control switch is suitable for electrical control circuits such as anti-theft alarm, remote control electric door and window, signal control, industrial control, lifting equipment and so on. Remote control switch module relay contact independent output, very suitable for direct control of various types of load; products use learning code wireless coding technology (space-to-space pair code), no directional, switch does not interfere with each other. Note: 12V remote control switch, the power supply is recommended to use more than 500mA DC regulated power supply. Working mode: Self-locking/interlocking/jogging user can adjust freely, which can realize one control multiple/multiple control one.The receiver board can withstand 10A per channel and can directly drive DC/AC loads, each with a set of normally open (normally closed) contacts. In order to extend the service life of the receiving board, not recommend controlling the high-power load. When controlling 220V, each control is less than 500W, and when controlling 12V, each control is less than 50W. Features: 1. Output relay switch: It can control the load of different voltages below 250V. The power supply must be 12V.2. Circuit board size: 35 x 30 x 17mm.3. Working mode: the self-locking, interlocking, jogging and delay working mode is adopted by short-circuiting the pin.4. Learning type code: You can learn the code with the same frequency remote control. (Don't worry if you lose the remote control during the process. Just buy a new remote control and learn it, no need to replace it, which greatly saves the user's cost. ). Learn how to code: 1. Jog learning method:Press the control board code button once, the LED indicator flashes once, then press the remote control button that needs to be coded. The LED of the control panel flashes several times continuously, indicating that the code is successful. 2. Self-locking learning method:Press the control board code button twice in succession, the LED indicator flashes twice, when the LED indicator goes out, then press the remote control button that needs to be coded. The LED of the control panel flashes several times continuously, indicating that the code is successful. 3. Interlocking learning method:>>>Product ID: 1348156<<<Different remote control can be selected to make the function more completePress the control board code button three times in succession, the LED indicator flashes 3 times, and after the LED indicator goes out, press the remote control A button and B button that need to be coded, and the control panel LED indicator flashes several times continuously. Indicates that the code is successful. 4. Delay 5 seconds learning method:>>>Product ID: 1348154<<<Different remote control can be selected to make the function more completePress the control board code button 4 times in succession. The LED indicator flashes 4 times. After the LED indicator goes out, press the remote control button that needs to be coded. The LED of the control panel flashes several times continuously, indicating that the code is successful. . 5. Delay 10 seconds learning method:>>>Product ID: 1348154<<<Different remote control can be selected to make the function more completePress the control board code button 5 times in succession. The LED indicator flashes 5 times. After the LED indicator goes out, press the remote control button that needs to be coded. The LED of the control panel flashes several times continuously, indicating that the code is successful. . 6. Delay 15 seconds learning method:>>>Product ID: 1348154<<<Different remote control can be selected to make the function more completePress the control board code button 6 times in succession. The LED indicator flashes 6 times. After the LED indicator goes out, press the remote control button that needs to be coded. The LED of the control panel flashes several times continuously, indicating that the code is successful. . Operating mode: 1. Jog mode(Default working mode): press the remote control relay to pull in, release the remote control relay to disconnect2. Self-locking mode(Default working mode): press the remote control relay to pull in, press again the remote control to disconnect3. Interlock mode(Need a different remote control): press the remote control A button, the relay pulls in, press the remote control B button to disconnect4. Delay mode(Need a different remote control): press the remote control relay to close, start the timer after releasing the remote control, and automatically turn off the relay after 5 seconds, 10 seconds, 15 seconds (3 speeds). Clearing code method: Keep pressing the learning button for about 8 seconds, the indicator flashes several times and then goes off, indicating that the clearing is successful. Matching wireless remote control transmitter: Dimensions: outer diameter 45mm, button diameter 30mmFrequency: 433MHzVoltage: 6V (built-in two CR2016 button batteries)Chip: Learning code ev1527Matching stickers can be attached anywhere. Package includes: 1 x Wireless remote control switch1 x Remote control (Battery insided)
