42V 350W 15A XT60 Motor Controller+Dashboard+Front/Rear Light For Scooter E-bike – 02#

Description

: Ultra-quiet, motor torque ripple is minimized to achieve no noise, no vibration and comfortable operation.Based on the Field Oriented Control FOC algorithm, the controller has high conversion efficiency, which can effectively reduce controller temperature rise and extend battery life. Specification: Operating Voltage Minimum:31V, Typical:35V, Maximum:45V Low Pressure Stop: Minimum:30.5V, Typical:31V, Maximum:31.5V, Remarks:The last cell flashes red Motor Current Limit 15±1A Quiescent Current 30uA Ambient Temperature Minimum:-30℃, Typical:35℃, Maximum:80℃ Rated Power 350W Overvoltage Protection 45V Stall Protection Delay 2 seconds Sleep Time 10 minutes Phase Angle 120 degrees Output Waveform Sine wave Motor matching 8.5 inches 15 pairs of poles Hall motor Shell Waterproof Rating Ordinary waterproof Instrument Matching PRO meter Motor Driven FOC vector algorithm Shell Size 118mm×48mm×32mm Housing Material Aluminum Features: 1.Power on,off: Short press 0.5 second,power on, long press 2 seconds to shut down。 2.Cycling mode:Non-zero start mode that is, press the accelerator to start when the sliding speed reaches 3KM,H , zero start mode turn the accelerator bar to start the motor in a stationary state . 3.Speed gear: 1 files 10KM,H, 2 files20KM,H, 3 files 25KM,H. Click to switch the gear with memory function, the default is the gear used before the last shutdown . 4.Electronic brake: Compatible with power-off brake and linear Hall brake. 5.Taillight：The light is always on and the brake flashes. 6.Constant speed cruise mode: 1.Fixed-speed cruise function turned on：When the accelerator speed control is stabilized in the riding mode, the cruise mode is automatically entered after 6 seconds. Press the brake, accelerator, switch gear, you can exit the cruise mode . 2. Fixed-speed cruise function turned off:No cruise was allowed during the ride. 7.Self-learning: first power on, run at no-load speed and keep the handlebar for 3 seconds, then release the handlebar for 5 seconds. After the motor drive stops, the motor parameters can be learned and saved automatically. 8.MOS tube breakdown protection: Before or when the controller is powered on, the D and S poles of the upper arm or lower arm of a phase MOS tube are short-circuited, the controller stops driving and has no output. You need to power on again after troubleshooting to work normally Power Display: 1 Voltage 38.2V-42V The first second third fourth fifth lights are always on 2 Voltage 36.6V-38.2V The first second third fourth light is always on 3 Voltage 34.5V-36.6V The first second third lights are always on 4 Voltage 32.8V-34.5V The first second light is always on 5 Voltage 31.5V-32.8V The first light is always on 6 Voltage 30-31.5V The last grid flashes 7 Turn-off of motor with voltage below 31V Error Code: 1 E1 Motor Hall failure 2 E2 MOS MOS fault or motor phase line short circuit fault 3 E3 Brake failure 4 E4 Handlebar failure 5 E5 Undervoltage protection 6 E6 Instrument,control communication failure 7 E7 Overvoltage protection 8 E8 Controller op amp failure 9 E9 Stall protection Wiring Port Diagram: Power cord: big black red wire Motor wire: blue wire,green wire,yellow wire Hall wire: red wire,yellow wire,blue wire,green wire,black wire Tail light wire: small red wire and black wire Software Burning line: green line,red line,black line Communication line: green line,blue line,black line,red wire ,yellow line Package Included: Type 01 1 X Controller 1 X Dashboard 1 X Accelerator 1 X Front Light 1 X Rear Light 1 X Waterproof Wiring Type 02 1 X Controller 1 X Dashboard